How to install solar carport - Antaisolar.com

 Antaisolar carport structure is ahighly pre-assembled ground mounting PV system. The special pre-assembled structure and unique beams & rails not only guarantee the whole system stability, but also make installation easier and faster. The high quality, small quantity and highly pre-assembled components greatly save installation time and cost, especially for a large-scale project.


Please check below installation steps carefully before start installation.


Step one：Installation of Concrete Foundation

Please prepare all necessary tools and products before installation. Firstly, mark the corresponding positions of concrete blocks according to the drawing, and bury the anchor bolts in the concrete blocks. The spacing of anchor bolts should follow the hole positions of aluminum base.



Step two：Installation of Pre-assembled Beam


Connecting pole to the beam by bolts & nuts, and connecting the pole to the bottom base, which fixed by the anchor bolts.


Note: The pre-assembled bolts of the mounting structure are not fully locked, which is convenient for adjustment during field installation. Please make sure all bolts are locked after installation.


Then continue with the same to install all supporting structures on the same plane.


Step three：Installation of Rail

Insert rail splice to connect rails with screws and then fixing the rails on beams by 4pcs rail clamp. Repeat above steps to install the other rails according to the drawing, and make sure all bolts are tightened.





Step four ：Installation of Modules

As shown in the figure below, place the module one by one (From left to right and from bottom to the top). 50mm is reserved at the end, which can be used to install grounding lug.  Then using mid and end clamps to fix the modules and make sure the modules and rails are tightly closed.



Step five：Installation of Grounding lug

Install the grounding lug and connect it one by one.



When adopting Antaisolar mounting structure, you can get the installation manual in details without any worry. Solar canopy emerged as a wise application to obtain solar power generation and car shading, for more project references please check out at: https://www.antaisolar.com/news/searchpcb



评论

发表评论

此博客中的热门博文

How to install solar panels on corrugated metal roofing | sic-solar.com

图片
  Can   solar panels   be mounted on a metal roof? For sure, metal roof is one of the best roof material to install solar panels, due to its durability and easy for installation. Either framed or frameless solar panels could be mounted, and the shadows of panels could keep your home cool during the summer. The Metal roof have various types. The corrugated steel roof is the basic type, which you can see everywhere. To fix solar panels on it, the solar mounting brackets need to penetrate the roof sheet and fix into the wooden or steel beam directly by screws or hanger bolts. Details as follow. 1.  L feet+self-tapping screws 2.  L feet+Solar hanger bolt L feet is widely used for its high adaptability, which do not have request on the size of metal roof sheet. For some project, below alu clamp will be developed to better adapt with the corrugated steel roof. But it is not proposed due to its unique adaptability.
阅读全文

How to Install Standing Seam Roof Mounting System by Klip lok 700 Roof Clamp?

图片
  GeneralIntroduction: Antaisolar  standing seam roof mounting system  is an convenient and ideal solar roof solution. Made of anodized aluminum 6005-T6 and SUS 304, Klip lok 700 roof clamp enables less installation time and offers secure fastening and water tightness without penetrating the roof sheet. Here is the installation guide of Klip lok 700 roof clamp for your information. InstallationProcess: a. Fixing the Klip lok 700 roof clamp b. Fixing the earthing clip c. Placing the solar panels and use the end clamps to fix the panel d. Using the mid clamps to fix the panel e. Placing the entire panel from bottom to top f. Installing the grounding lug More installation details at  https://www.youtube.com/watch?v=OQr8xVhJE40 Installation precautions: Ø The bolts of the Klip lok 700 roof clamp are pre-assembled, and can be easily tightened after adjusting the clamp position. Ø The rubber pad at the bottom of the Klip lok 700...
阅读全文

A brief introduction to the earthing washer/grounding clips in solar mounting system

图片
  Grounding PV modules  to reduce or eliminate shock and fire hazards is necessary and required by Electrical Code in countries in USA, Australia etc. The grounding guidelines of the Code es sentially state that all electrical equipment is to be grounded by means of direct attachment to an equipment grounding conductor. This can be done in many different ways. The traditional method is to use the ground bond point of each  solar panel  and connect all the panels together with heavy gauge bare copper wire. This approach can be difficult, time-consuming and costly. Some of the difficulties in grounding PV modules arise from the fact that copper conductors are typically used for electrical connections while the module frames are generally made of aluminum. The incompatibility of copper and aluminum was discovered from numerous fires in houses wired with aluminum wiring in the 1970’s. Copper and aluminum will also react and corrode. The surfaces of aluminum frames are an...
阅读全文