Rooftop solar mount installation instruction | Artsignenergy.com

 Introduction of distributed photovoltaic system

Solar PV On-grid system

Schematic diagram of distributed photovoltaic system principle


Schematic diagram of distributed photovoltaic system

Solar brackets installation


Schematic diagram of solar tile roof mount kits installation


Tileroof bracket installationinstruction:

Schematic diagram of solar tile roof mount kits


Metal rooftop roof pv mounting system


Solar pv flat roof mount structure installation:

Metal rooftop roof pv mounting system


Flat concrete rooftop pv mounting structure

Flat concrete rooftop pv mounting structure


Cleaning the roof debris, use a measuring tape to measure the installation position of the foundation on the roof, and place the foundation;

Use a percussion drill to drill holes in the cement foundation. The depth of the hole is determined by the thickness of the foundation and the length of the bolt. The bolt diameter is M10. (The pre-embedded bolts are used to deal with impurities on the threads);

Put the expansion bolt into the hole, use a non-metal hammer such as a wooden hammer or a leather hammer to gently tap the bolt into the hole, with a distance of 30mm from the hole;


Installing the bottom beam or foundation, align the bottom beam hole or foundation hole with the bolt and use a wrench to tighten the nut; (fix other foundation foundations according to the above method)


Measuring the installation position of the rear column according to the angle of the bracket, and use bolts to fix the base to the rear column;

Fix the inclined beam, use the corner connection to fix the rear pillar, and use the bolt to connect the inclined beam to the base;

Fixing the keel, determine the installation position of the keel according to the installation hole of the component, keep the distance between the keel and the installation hole at ±100mm, and the frame at both ends of the component is 200-300mm away from the inclined beam. Use special-shaped nuts to fix the keel on the inclined beam;


Before installing the module, determine the installation height of the module. The glass surface of the lower end of the module is 300mm away from the ground. Use the side pressure block to fix the module. First fix the lower end pressure block to prevent the module from sliding. The module frame is 20-30mm away from the two ends of the keel. Two people are required to cooperate when fixing, and use a wire drawing method or a level to determine the overall parallelism of the components.


If you have any inquiry or question about pv mounting brackets, welcome to contact Art Sign.
Email: sales@artsign.net.cn Whatsapp/Wechat/Skype: + 86 180 3023 5875   Art Sign


评论

发表评论

此博客中的热门博文

How to Install Standing Seam Roof Mounting System by Klip lok 700 Roof Clamp?

图片
  GeneralIntroduction: Antaisolar  standing seam roof mounting system  is an convenient and ideal solar roof solution. Made of anodized aluminum 6005-T6 and SUS 304, Klip lok 700 roof clamp enables less installation time and offers secure fastening and water tightness without penetrating the roof sheet. Here is the installation guide of Klip lok 700 roof clamp for your information. InstallationProcess: a. Fixing the Klip lok 700 roof clamp b. Fixing the earthing clip c. Placing the solar panels and use the end clamps to fix the panel d. Using the mid clamps to fix the panel e. Placing the entire panel from bottom to top f. Installing the grounding lug More installation details at  https://www.youtube.com/watch?v=OQr8xVhJE40 Installation precautions: Ø The bolts of the Klip lok 700 roof clamp are pre-assembled, and can be easily tightened after adjusting the clamp position. Ø The rubber pad at the bottom of the Klip lok 700 roof clamp needs to be fixed tightly to the metal roof surface.
阅读全文

How to install solar panels on corrugated metal roofing | sic-solar.com

图片
  Can   solar panels   be mounted on a metal roof? For sure, metal roof is one of the best roof material to install solar panels, due to its durability and easy for installation. Either framed or frameless solar panels could be mounted, and the shadows of panels could keep your home cool during the summer. The Metal roof have various types. The corrugated steel roof is the basic type, which you can see everywhere. To fix solar panels on it, the solar mounting brackets need to penetrate the roof sheet and fix into the wooden or steel beam directly by screws or hanger bolts. Details as follow. 1.  L feet+self-tapping screws 2.  L feet+Solar hanger bolt L feet is widely used for its high adaptability, which do not have request on the size of metal roof sheet. For some project, below alu clamp will be developed to better adapt with the corrugated steel roof. But it is not proposed due to its unique adaptability.
阅读全文

A brief introduction to the earthing washer/grounding clips in solar mounting system

图片
  Grounding PV modules  to reduce or eliminate shock and fire hazards is necessary and required by Electrical Code in countries in USA, Australia etc. The grounding guidelines of the Code es sentially state that all electrical equipment is to be grounded by means of direct attachment to an equipment grounding conductor. This can be done in many different ways. The traditional method is to use the ground bond point of each  solar panel  and connect all the panels together with heavy gauge bare copper wire. This approach can be difficult, time-consuming and costly. Some of the difficulties in grounding PV modules arise from the fact that copper conductors are typically used for electrical connections while the module frames are generally made of aluminum. The incompatibility of copper and aluminum was discovered from numerous fires in houses wired with aluminum wiring in the 1970’s. Copper and aluminum will also react and corrode. The surfaces of aluminum frames are anodized or have powd
阅读全文