Solar mounting system

  What is bifacial module? The bifacial module, as the name implies, can generate electricity on both the front and backside of the modules. Compared with conventional single-sided modules, it can increase power generation by about 10-30%. From a technical point of view, the bifacial modules and   solar trackers   are a effective way to reduce the cost of electricity in the photovoltaic industry. ​ The shading of the front of the module is often the focus of attention. However, for the bifacial module, since the back side also has the power generation capacity, the shading of the back also needs to be paid attention to, especially the shading from the solar bracket. For conventional solar brackets, the design of the main supporting beam and purlin is more concerned with strength, economy and the location of the component bolt holes (or clamps). As for the bifacial module, the solar racking system needs to be specially designed. Firstly, the main supporting beam and purlin of the mounti

  Solar Carport : parking and power generation is compatibility. The photovoltaic panel is installed above the carport. When viewed from the outside, it is an ordinary solar carport, which can protect the vehicle from the wind and sun. Under each carport, there is a combiner box. The solar panel at the top of the shed is used to uniformly store the absorbed power, and then transmitted to the inverter to change DC into AC, which can be transmitted to the power grid to  complete power generation. Solar carport system  power generation : This is not only a new power generation mode ,also the development trend of future. It can be installed early to enjoy benefit early. As long as the solar module power generation system is installed on the sunny roof, it can convert solar energy into electric energy to supply residents' domestic power or industrial power of the factory. Roof power generation is different from the traditional centralized ground solar power system. It has the characteri

  Solar carport system , the most simple and easy way to combine photovoltaic and architecture, which has been more and more popular in recent years. The  photovoltaic carport system  has good heat absorption, convenient installation and low cost. It can not only make full use of the original site, but also provide green energy. The construction of photovoltaic sheds photin factory parks, commercial areas, hospitals and schools can solve the problem of high temperature in open-air parking lots in summer. Use the idle area of the parking shed to build a solar parking shed. In addition to supplying the power for vehicles, the excess power can also be sold to the state, which not only has a very good income, but also reduces the power pressure of the city. Solar carport system brings benefits while saving energy: Investing in the construction of photovoltaic parking shed will change the single role of traditional parking shed.  solar parking shed  can not only shade vehicles from the sun

  The right choice of   solar racking   material can impact the economic performance and stability of a solar power plant. So how to choose the right bracket according to the material? Generally, the main materials of solar racking are carbon steel, aluminum alloy. and new materials, carbon steel and aluminum alloy are widely used in the PV market. The  aluminum alloy made solar racking  is aesthetically pleasing. Its main advantage is light-weight, which is one-third of the weight of carbon steel. The surface is highly corrosion-resistant, forming a dense oxide film protective layer in the air to further prevent oxidation. In addition, aluminum alloy still has a recovery rate of 65% after 25 years of the life cycle of the power station, which is environmentally friendly and recyclable. In terms of production and processing, aluminum profiles can be easily processed into various specifications through sawing, drilling, punching and other processes, making it more flexible and easy to i

  General Introduction: The  railless metal roof mounting system  facilitates the rapid mounting of framed PV modules on metal sheet roofs with minimum thickness 0.8mm, only four components are required to install the modules directly to the roof. A base mounting clip is 100mm or 140mm long, which is easy to carry and attach to almost all trapezoidal and sandwich roofs. The EPDM sheet is in the package to seal the screw against the metal sheet. Installation Process: a.Fixing the TYN-47 roof clamp according to layout b. Placing the solar panels and use the end clamps to fix the panels c. Using the mid clamps to fix the panels d. Placing the entire panel from bottom to top For more installation details, please view the video below Installation precautions: ***Measuring the width of the standing seam to ensure that the roof clamps can match with it ***The three self-tapping screws of the TYN-47 roof clamp are pre-assembled, and can be easily fastened after adjusting the clamp position. **

  Since 2006,   ART   SIGN  mainly produce the solar rooftop mounting system, solar ground mounting system includes relative solar racking accessories solar roof hook, solar module clamps and stainless steel roof hook ect. According to different installation site,  ART   SIGN  fabricate various of roof hooks for solar mounting systems ,Below please see our normal design of stainess hooks . Solar stainl ess steel hook type-1 AS-RH- 01 Solar stainless steel hook type -2 AS- RH-03 Solar stainless steel hook type-3 (same as 01 different direction installation AS-RH-04 Solar stainless steel hook type -4(adjustable hook) AS-RH-14 Specification of solar roof hook Material: SUS304 ,we have many another different styles for the roof hooks . Package of roof hooks  : The installation difference

  For solar power stations, in order to ensure the whole system stability and reliability during the 25-year operation period, especially in the areas of severe weather conditions such as typhoons, it’s essential to conduct pull-out force test for the   solar racking   adapted. For different roof types, the roof clamps adapted can be different, but the test method is the same. Taking an example of Kliplok ®700 non-penetrating roof clamps, the test procedures are as following: First, lock the fixture to the section of roof sheeting. Then use the iron wire to wrap around the fixture, and then use the tension meter to count. It requires two people to lift it up together, and the tester records the data. Take points to test in different places to ensure the accuracy of the test. According to the local wind load requirements, apply the corresponding pulling force to check whether the fixture is not damaged or cracked. If the test results meet the requirements of the project engineering, the

  Aluminum roof brackets  is one of the solar systems components to fit most of standing seam metal roof profiles and then combine with  rails ,  mid & end clamps  and other components to work as solar roof racking solution. Made of Aluminum 6005-T5 with stainless steel hardware, Art Sign offers a variety of roof brackets to fit different standing seam profile. Generally, it is divided into two kinds of clamps, that is non-penetration and penetration. For non-penetration roof clamps like the following items, the round point setscrews compress the seam material against the opposite wall of the clamps. They will dimple the seam material, but will not penetrate it. For penetration roof clamps like trapezoidal roof sheet, it’s designed with EPDM between roof and clamps to prevent from water leakage. For whatever roof sheet profile, Art Sign can always offer any kinds of roof brackets to well fit the roof. Art   Sign   has been manufacturing solar mounting systems  (roof mounting ,  gro

  In solar panel mounting, because some product are not suitable for some roofs, there is new hook for plain tile roof that won't damage the tile roof,   SIC   has two new products for tile roof solar panel installation: plain tile roof hook and adjustable end clamp. 1.  Plain tile roof hook This hook is thinner than regular roof hook, but its contact surface with the roof and rail is larger than the regular one. There are many kind of tile roofs, and the regular roof hook is suitable for the corrugated tile roof, while the new hook is more suitable for the flat tile roof. 2.  Adjustable End Clamp The clamp is suitable for that thicker than 35mm module, and this clamp is more flexible than other fixed clamp, you don't need to be worried when the module is so thick that the clamp is not suitable.