SUNKEAN CPR certified H1Z2Z2-K Solar Cable | Sunkean.com

 Under the European Construction Products Regulation (CPR), all Solar cable manufacturers and suppliers are now required to apply CE marking to all cables permanently installed in all household, commercial or industrial buildings or civil engineering work in the European Union. The standard for cables, EN 50575, defines the test standards for testing the 'Reaction to Fire' performance of a cable and also the method of classifying this performance. As far as cables are concerned, the legislation applies to power, telecommunications, data and control cables.


Solar Energy Products Manufacturer


An increasing number of solar installers require Cca class cables to comply with the European standard. In public places rooftop installations (supermarkets, hospitals and similar) solar cable feeds the transformers which are located inside the building, never on the roof. Therefore, according to the Construction Products Regulation (CPR), minimum fire reaction class required for cables must be Cca.


SUNKEAN H1Z2Z2-K cable is B2ca certified and also TÜV certified according to EN 50618. Both certifications guarantee that SUNKEAN H1Z2Z2-K cable is fully functional in both solar photovoltaic farms and in industrial -or residential- rooftop photovoltaic installations.


EN 50618 H1Z2Z2-K Solar Cable


SUNKEAN H1Z2Z2-K cable is resistant to UV rays, ozone, sand abrasion and water absorption, withstanding severe environmental conditions (corrosion, climate and extreme hot and cold environments). It also can be installed in places where water is present (AD7).




Our H1Z2Z2-K cable is available in a wide range of cross-sections (1x4mm2,1x6mm2, etc.) and formats (3000m、2000m、1000m and 500m reels), with a red or black cover.


If you are interested in our products, please feel free to contact us. Thank you!



评论

发表评论

此博客中的热门博文

A brief introduction to the earthing washer/grounding clips in solar mounting system

图片
  Grounding PV modules  to reduce or eliminate shock and fire hazards is necessary and required by Electrical Code in countries in USA, Australia etc. The grounding guidelines of the Code es sentially state that all electrical equipment is to be grounded by means of direct attachment to an equipment grounding conductor. This can be done in many different ways. The traditional method is to use the ground bond point of each  solar panel  and connect all the panels together with heavy gauge bare copper wire. This approach can be difficult, time-consuming and costly. Some of the difficulties in grounding PV modules arise from the fact that copper conductors are typically used for electrical connections while the module frames are generally made of aluminum. The incompatibility of copper and aluminum was discovered from numerous fires in houses wired with aluminum wiring in the 1970’s. Copper and aluminum will also react and corrode. The surfaces of aluminum frames are anodized or have powd
阅读全文

Three popular rail for pitched roof | sic-solar.com

图片
  High Quality solar aluminum rail for solar panel install.   SIC   provides different kinds of mounting rail to meet requirements from various customers. Below three type rails are very popular between our customers. ​ 1.  Side mountable aluminium rail Smart patented rail design--"Tilt in Module" could be slide in at any position of rail. 2.  40*40 mounting rail High efficiency design, which is cooperate with quick mount mid and end clamp to save installation time. 3.  Mini rail   /  Short rail Raliless design can reduce the weight on the roof, meanwhile can help our customers to save more cost.
阅读全文

How to install solar panels on corrugated metal roofing | sic-solar.com

图片
  Can   solar panels   be mounted on a metal roof? For sure, metal roof is one of the best roof material to install solar panels, due to its durability and easy for installation. Either framed or frameless solar panels could be mounted, and the shadows of panels could keep your home cool during the summer. The Metal roof have various types. The corrugated steel roof is the basic type, which you can see everywhere. To fix solar panels on it, the solar mounting brackets need to penetrate the roof sheet and fix into the wooden or steel beam directly by screws or hanger bolts. Details as follow. 1.  L feet+self-tapping screws 2.  L feet+Solar hanger bolt L feet is widely used for its high adaptability, which do not have request on the size of metal roof sheet. For some project, below alu clamp will be developed to better adapt with the corrugated steel roof. But it is not proposed due to its unique adaptability.
阅读全文